EP-HGA.ES-2C200 Automatic PET Blow Molding Machine — 2500ml, 2 Cavity, Large-Format Cosmetic, Edible Oil & Food Bottles

200mm Mold Close — 180mm Body Diameter

The 200mm blow mold close enables the widest body diameter available in the ES 2-cavity series at 180mm. This configuration is specifically required for institutional bulk containers, wide-grip edible oil jugs, and large-format food service containers where body diameter above 130mm is a functional or aesthetic design requirement that smaller mold-close machines cannot meet.

2,500ml Maximum Container Volume

At 2,500ml maximum volume, the ES-2C200 extends RSBM production into the large-format container category — institutional shampoo containers, 2-litre edible oil, and 2.5-litre food service containers — that the smaller ES-2C150 at 1,500ml maximum cannot reach. The 350mm maximum container height provides the dimensional depth to produce tall 2,500ml containers alongside wide short formats.

138mm Maximum Neck Diameter

The 138mm maximum neck diameter is significantly wider than smaller ES models, accommodating large-format pour spouts, wide-mouth food service openings, and institutional pump-dispenser necks that require diameter ranges above 100mm. This neck capability is a functional requirement for bulk containers where a wide opening is needed for pump or dispenser fitment.

High-Force Clamping for Wide Molds

Wider mold faces at 200mm require proportionally higher clamping force to maintain complete mold seal integrity during the blow phase at pressures up to 35 kg/cm². The EP-HGA.ES-2C200’s clamping system is specifically engineered for the wider mold-face geometry of large-body containers, preventing the mold-flash and parting-line leakage that occurs when standard clamping forces are applied to oversize mold configurations.

Extended Stretching Stroke — 500mm

The 500mm stretching stroke — longer than the 350–450mm range of smaller ES models — accommodates the extended axial stretch required to produce tall 2,500ml containers with the biaxial orientation necessary for adequate mechanical strength and gas barrier performance at this volume. The longer stroke is a structural prerequisite for large-format container production, not merely a capacity upgrade.

Servo-Driven Efficiency at Large Format

The extended cooling time inherent to 2,500ml containers creates a proportionally larger opportunity for energy recovery during the dwell phase. The servo drive system on the ES-2C200 recovers kinetic energy during each deceleration phase and reapplies it to subsequent motion cycles — a measurable energy advantage over hydraulic-primary RSBM machines at this output level and container volume.

Institutional Cosmetic Dispensers

Bulk 2,000ml–2,500ml salon shampoo, conditioner, and body wash dispensers for professional salon supply, hotel amenity programs, and gym facilities. The 180mm body diameter enables the wide stable base and large pump-fitment neck required for institutional dispensers that must withstand repeated use in commercial environments.

2-Litre Edible Oil Jugs

2,000ml and 2,500ml edible oil jugs with wide grip zones, wide-mouth pour spouts, and extended label panels. The wide 138mm neck diameter supports large-format flip-cap pourers and dispensing caps used in food service and institutional cooking applications where controlled high-volume pouring is required.

Large-Format Food Service Containers

Industrial sauce containers, bulk condiment jugs, and food service large-format packaging in the 2,000ml–2,500ml range for catering supply and food service distribution channels. The combination of large volume and wide body geometry is a specific requirement of food service packaging that standard RSBM configurations cannot address.

Aplikasi: 2,000ml PET institutional hand wash and body wash dispensers for a Saudi hygiene products supplier serving hospitals, hotels, and commercial facilities across the Gulf region.

Masalah terpecahkan: The supplier needed containers with a 165mm body diameter to accommodate their existing pump-station bracket system — a dimension that no standard RSBM machine below the ES-2C200’s 180mm maximum could produce. The ES-2C200 was the only machine in the ES series capable of producing this specific body diameter without requiring redesign of the supplier’s existing pump station infrastructure.

“Our pump stations were already installed in 200 facilities. We needed a bottle that fit, not a new pump station. This machine was the only one that could produce the 165mm diameter we required.”

Aplikasi: 2,000ml and 2,500ml PET olive oil jugs for a Spanish olive oil cooperative supplying food service distributors in Spain, France, and Germany.

Masalah terpecahkan: The cooperative required a wide-grip jug design with a 170mm body diameter for ergonomic pouring in food service kitchens. Glass at this format was too heavy and fragile for kitchen environments. The ES-2C200 produced PET jugs matching the required diameter at 30% of the glass weight, with a UV additive in the preform maintaining oil quality during the extended shelf life required for food service supply chains.

“Chefs in commercial kitchens need a jug they can grip and pour with one hand. The 170mm diameter and the weight reduction from glass to PET made that possible. Our food service customers have re-ordered at higher volumes.”

Aplikasi: 2,500ml PETG protein powder containers with 138mm wide-mouth opening for a major Australian sports nutrition brand supplying specialty retail and direct-to-consumer channels.

Masalah terpecahkan: The brand required a 2,500ml container with both a 138mm wide-mouth opening (to fit a standard scoop) and a 175mm body diameter for stable shelf presentation. No injection-moulded container could meet both specifications at that volume economically. The ES-2C200 producing PETG met both the neck and body diameter specifications simultaneously, at a cost-per-unit significantly below the injection-moulded alternative.

“Wide mouth, wide body, 2.5 litres. The combination of all three in a single PET container — at a cost below injection moulding — was what made this machine selection straightforward.”