Deskripsi
European-Architecture Injection Blow Molding — 40 Tonne Class
CE-Certified European IBM in the Uniloy UIB70 Output Class — Lower Running Cost, Broader Parts Access
Buyers assessing the Uniloy UIB70 class often weigh American heritage against the total cost of long-term operation. The EP-ZQ40 offers a European-architecture alternative: CE marking, European-sourced critical components and an operating power ratio of 52 to 70% of installed capacity — cited here only to assist specification comparison, with no affiliation to Uniloy.
EP-ZQ40 vs Uniloy UIB70 — Specification Comparison
Uniloy pioneered IBM technology and the UIB series remains a widely installed reference point in pharmaceutical and personal care packaging plants. Buyers re-equipping existing UIB70 lines or specifying new capacity in export markets are increasingly weighing European-architecture machines alongside the established American standard. The table below presents key figures side by side. Uniloy UIB70 data is sourced from publicly available specification material. Uniloy is referenced solely to assist buyers in equipment comparison and is not affiliated with Ever Power.
| Parameter | Uniloy UIB70 | Ever Power EP-ZQ40 |
|---|---|---|
| Injection Clamping Force | ~350 kN | 400 kN |
| Diameter Sekrup | 40 mm | 40/45 mm |
| Berat Injeksi | 160 g | 190/260 g |
| Mold Size (L x W) | 460 x 300 mm | 480 x 340 mm |
| Machine Size (L x W x H) | 3.8 x 1.4 x 2.1 m | 3.5 x 1.3 x 1.7 m |
| Compliance Marking | UL / ANSI | CE (EU Machinery Directive) |
| Max Cavities — 10 ml | — | 9 |
| Operating Power Ratio | — | 52 to 70% of 20 kW |
Uniloy UIB70 reference figures sourced from publicly available specification data. Uniloy is cited only to assist buyers in equipment comparison and is not affiliated with Ever Power.
EP-ZQ40 Full Technical Specifications
Pharmaceutical and cosmetic packaging plants in Europe, Australia and export-regulated markets routinely require CE marking as a precondition for machine import and GMP line qualification. The EP-ZQ40 carries full CE marking under the applicable EU Machinery Directive — documentation available with the machine and in advance for procurement. Its European pressurized-clamping architecture also delivers a measurable energy advantage: actual operating power runs at 52 to 70% of the 20 kW installed capacity, compared with the constant-pressure hydraulic circuit used in older American IBM designs. Full specifications are tabulated below; see the complete ZQ range at the IBM machines overview.
Injection System
| Parameter | Unit | Value |
|---|---|---|
| Diameter Sekrup | mm | 40 / 45 |
| Screw L/D Ratio | — | 22:1 |
| Berat Injeksi | g | 190 / 260 |
| Heating Power | kW | 7.5 |
| Number of Barrel Zones | — | 3+N |
| Injection Stroke | mm | 120 |
Clamping System
| Parameter | Unit | Value |
|---|---|---|
| Injection Clamping Force | kN | 400 |
| Injection Opening Stroke | mm | 165 |
| Gaya Jepit Tiup | kN | 60 |
| Blow Opening Stroke | mm | 140 |
| Rotary Table Lift Height | mm | 70 |
Mould
| Parameter | Unit | Value |
|---|---|---|
| Max Platen Size (L x W) | mm | 480 x 340 |
| Mold Thickness | mm | 180 |
| Max Bottle Diameter | mm | 120 |
| Max Bottle Height | mm | 220 |
| Max Bottle Volume | ml | 1 to 1500 |
| Stripping Stroke | mm | 220 |
Hydraulic System and Utilities
| Parameter | Unit | Value |
|---|---|---|
| Hydraulic Pressure | MPa | 14 |
| Tenaga Motor | kW | 11 |
| Dry Cycle | s | 3.5 |
| Daya Total | kW | 20 |
| Operating Power Ratio | % | 52 to 70 |
| Min Air Pressure | MPa | 0.7 to 1.2 |
| Compressed Air Capacity | m3/min | 0.7 |
| Cooling Water Flow | m3/h | 3.5 |
| Cooling Water Pressure | MPa | 0.3 to 0.4 |
| Machine Dimensions (L x W x H) | m | 3.5 x 1.3 x 1.7 |
| Net Weight | ton | 3.8 |
Parameters are for reference only. Ever Power reserves the right to modify specifications without prior notice.
Cavity Output by Bottle Volume
For pharmaceutical oral liquid and ophthalmic packaging lines, cavity count at 10 and 30 ml is the primary throughput driver. The EP-ZQ40 supports 9 cavities at 10 ml and 8 at 30 ml — and because the 480 x 340 mm platen is larger in both dimensions than the 460 x 300 mm of the UIB70 class, the cavity layout can accommodate slightly wider neck tooling or additional clearance between positions without redesigning to a larger machine.
| Volume | 10 ml | 30 ml | 60 ml | 100 ml | 250 ml | 500 ml | 1000 ml |
|---|---|---|---|---|---|---|---|
| Max Cavities | 9 | 8 | 6 | 4 | 3 | 2 | 1 |
For reference only. Actual cavity count depends on mold design and bottle geometry.
Why Buyers in the UIB70 Class Consider European-Architecture IBM Machines
CE Marking vs UL — Export Market Access
The UIB series carries UL and ANSI compliance appropriate for North American installations. The EP-ZQ40 is CE marked under the EU Machinery Directive, which is the required compliance standard for pharmaceutical packaging equipment in the EU, UK, Australia, and many regulated export markets. For producers supplying European or GMP-qualified lines, CE documentation is a procurement requirement that UIB-class machines cannot satisfy without additional re-certification work.
Lower Operating Power — 52 to 70% of Installed Capacity
The European pressurized-clamping structure uses a booster cylinder that is active only during the brief clamping phase, independent of the mold-open and mold-close sequence. This means the hydraulic circuit is under full load for a small fraction of each cycle. Actual operating power on the EP-ZQ40 runs at 52 to 70% of the 20 kW installed capacity — a meaningful reduction in per-shift energy cost over years of continuous pharmaceutical line operation.
European Component Supply — Global Parts Availability
The EP-ZQ40 sources hydraulic seals from HALLITE (England), pneumatic valves from Festo (Germany), position sensors from Gefran (Italy) and electrical contactors from Schneider (France). These are standard industrial components with distributor networks across Europe, Asia and the Americas. Maintenance teams in markets outside North America typically find European-standard parts significantly easier to source on short lead times than UIB-specific American components.
Higher Injection Weight: 190/260 g vs 160 g
At 190 to 260 g versus 160 g for the UIB70 class, the EP-ZQ40 supports heavier preforms — 19 to 63% more injection weight depending on screw selection. For lines running larger bottles at the upper end of the 1500 ml volume range, or processing denser engineering resins such as PCTG, this additional injection capacity avoids the need to step up to a larger machine class.
Smaller Installed Footprint in All Three Dimensions
The EP-ZQ40 at 3.5 x 1.3 x 1.7 m is 0.3 m shorter, 0.1 m narrower and 0.4 m lower than the UIB70 class at 3.8 x 1.4 x 2.1 m. The 0.4 m height reduction is particularly relevant in pharmaceutical clean rooms where ceiling clearance is often the constraint on machine selection — a 1.7 m machine installs under significantly more ceiling configurations than a 2.1 m one.
400 kN Clamping — 14% Above the UIB70 Class
The EP-ZQ40 injection clamping force of 400 kN is approximately 14% above the UIB70 class figure of 350 kN. Combined with the European pressurized-clamping architecture, this additional force headroom provides more consistent preform filling across all nine cavities at 10 ml during sustained multi-shift pharmaceutical production.
Component Origins — European Industrial Supply Chain
One practical consideration when moving from UIB-class machines to a European alternative is component continuity. The EP-ZQ40 is built around industrial components from established European and Taiwanese manufacturers — Schneider, Festo, HALLITE, Gefran, Ekor and Hongxun — all with standard distributor networks outside North America. This matters most for maintenance teams running pharmaceutical lines where unplanned downtime has direct GMP compliance consequences.
| TIDAK. | Component | Supplier | Origin |
|---|---|---|---|
| 1 | Computer | Hongxun | Taiwan |
| 2 | Penggerak Servo Pompa Oli | Hongxun | Taiwan |
| 3 | Motor Servo | Fisi | Italia |
| 4 | Pompa Oli | Ekor | Jerman |
| 5 | Katup Hidrolik | Penelitian Minyak | Taiwan |
| 6 | Motor Bintang Lima | Staver (orang Haiti) | Cina |
| 7 | Penggaris Elektronik | Gefran | Italia |
| 8 | Kontaktor AC | Schneider | Perancis |
| 9 | Relai Pemanas | YANMING | Taiwan |
| 10 | Cincin Tipe O | HALLITE | Inggris |
| 11 | Cincin Segel | HALLITE | Inggris |
| 12 | Sakelar Perjalanan | YANMING | Taiwan |
| 13 | Saklar Udara | Schneider | Perancis |
| 14 | Pipa Minyak | ISR | Amerika Serikat |
| 15 | Katup Udara | Festo | Jerman |
| 16 | Motor Putar Servo | Huichuan | Cina |
| 17 | Karton PCS | Mecano | Cina |
Component suppliers may be substituted with equivalent or superior alternatives subject to availability without prior notice.
Compatible Materials and Industry Applications
The UIB70 class is most commonly found on pharmaceutical oral liquid, ophthalmic and nasal packaging lines. The EP-ZQ40 covers the same application base — HDPE, PP and PS for standard pharmaceutical formats — and extends into PCTG and bio-based PLA for producers supplying EU markets where material sustainability declarations are increasingly required alongside CE documentation.
Processable Materials
Farmasi
Ophthalmic liquid containers, nasal spray, oral liquid vials, syrup bottles — the primary UIB70 application base
Cosmetic
Serum vials, lotion and toner bottles, PCTG premium cosmetic containers for EU and export markets
Food and Beverage
Sauce bottles, edible oil containers, condiment packaging, dairy product bottles in food-contact compliant materials
Bio-Based and Sustainable
PLA and PCTG containers for EU-market brands with sustainability labelling requirements or recyclability declarations
Mold Tooling and GMP Compatibility
Producers transitioning from UIB-class tooling to the EP-ZQ40 need to commission new molds designed for the ZQ40 geometry. The 480 x 340 mm platen is 20 mm longer and 40 mm wider than the UIB70 class, so existing UIB70 tooling does not transfer directly — but the larger platen provides more layout flexibility for the replacement mold design, particularly for neck tooling with wider flange diameters common in pharmaceutical wide-mouth packaging. Injection mold bodies are available in 4Cr13 stainless or imported S136 alloy steel; blow mold bodies in magnesium-aluminium for faster thermal cycling.
Larger Platen Than UIB70 — More Layout Flexibility
At 480 x 340 mm versus 460 x 300 mm for the UIB70 class, the EP-ZQ40 platen provides 20 mm more length and 40 mm more width — useful headroom when designing replacement tooling with wider neck diameters or additional inter-cavity spacing for GMP air-flow requirements.
S136 and 4Cr13 Pharmaceutical-Grade Steel
Injection mold bodies from S136 high-strength alloy or 4Cr13 stainless steel. Both grades are appropriate for pharmaceutical packaging tooling requiring surface finishes compatible with GMP inspection standards and long-cycle tool life.
Zero Flash — No Secondary Trim Operation
The three-station injection blow process produces no parting-line flash, no gate mark and no runner waste. For pharmaceutical packaging, this also means no secondary trim debris that could contaminate the container interior — a GMP advantage over extrusion blow alternatives in the same capacity class.
Production Line Integration
The EP-ZQ40 installs as the central machine in a complete pharmaceutical or cosmetic bottle line. Its smaller footprint versus the UIB70 class simplifies clean-room layout planning and downstream equipment positioning. Ever Power supplies whole-line turnkey proposals or individual ancillaries to complement existing production infrastructure. View the full IBM machine range at the IBM machines overview.
Questions Buyers Ask When Evaluating Beyond the UIB70
Related IBM Machines
Looking beyond the Uniloy UIB70 class?
Get a detailed specification sheet, CE documentation and a line-by-line cost comparison from our technical team.
